And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Fresenius 2008 Machine Manual.To get started finding Fresenius 2008 Machine Manual, you are right to find our website which has a comprehensive collection of manuals listed.
If there is a survey it only takes 5 minutes, try any survey which works for you. If a TMP alarm reoccurs perform parts A and B up to twice more. Waltham, MA 02451 Manufactured by: Fresenius USA, Inc. Nelson Avenue Concord, CA 94520 REGIONAL EQUIPMENT SPECIALIST. Nelson Avenue Concord, CA 94520 Copyright 2017 Fresenius Medical Care North America, All Rights Reserved. These include the SENSORS, ACTUATOR, Acid (16) and Bicarbonate (17) Pumps, Blood Leak Sensor (8), Heparin Pump (18) and the Blood Pressure Module Continued on next page 2008T Troubleshooting Guide Page 3 PN 490292 Rev. Procedures may vary depending on if the machine is equipped for bibag. See the following page: 2008T Troubleshooting Guide Page 4 PN 490292 Rev. ENSURE the machine remains clear of all alarms before troubleshooting PRESSURE TEST FAILURES. End of The Order of Troubleshooting 2008T Troubleshooting Guide Page 6 PN 490292 Rev. The CBE board moves the Air Sensor Connector two-pins higher than the others CBE Change Being Effected Parts 3 through 6 next page 2008T Troubleshooting Guide Page 7 PN 490292 Rev. A problem located, and repaired, during INITIAL CHECKS may have solved the problem you were troubleshooting If not, return to the procedure that brought you to INITIAL CHECKS. T Troubleshooting Guide Page 9 PN 490292 Rev. It interfaces the bibag hydraulic components, Actuator-Test Board and the bibag Distribution Board and Distribution Box 2. Figure 4C bibag Interface Board 2008T Troubleshooting Guide Page 11 PN 490292 Rev. End of Final Checks 2008T Troubleshooting Guide Page 15 PN 490292 Rev. H) Measure at the Extender Boards 12V measuring point (five (5) pins from the left). Parts I through P next page 2008T Troubleshooting Guide Page 17 PN 490292 Rev. END OF VOLTAGE DETECTOR CALIBRATION 2008T Troubleshooting Guide Page 18 PN 490292 Rev. End of How to Enter T and C Mode 2008T Troubleshooting Guide Page 19 PN 490292 Rev. End of How to Enter a Cleaning Disinfection Program 2008T Troubleshooting Guide Page 21 PN 490292 Rev. If it ever runs empty Loading Pressure becomes unstable Call debug screen 0. Figure below, ENSURE the bibag Connector door is shown FULLY closed See procedure number F- 1.0.2 (page 25). LEFT BLANK INTENTIONALLY 2008T Troubleshooting Guide Page 24 PN 490292 Rev. LEFT BLANK INTENTIONALLY 2008T Troubleshooting Guide Page 29 PN 490292 Rev. Perform parts a AND b below: Close the shunt door page 141 NOTING which motor is not rotating properly, proceed to TROUBLESHOOTING MOTORS Figure 7 Deaeration AND Flow Motor 2008T Troubleshooting Guide Page 30 PN 490292 Rev. Hydraulics Front View LEFT BLANK INTENTIONALLY 2008T Troubleshooting Guide Page 32 PN 490292 Rev. Is EMPTY (left column) 1 2008T Troubleshooting Guide Page 38 PN 490292 Rev. To prevent Cond Offset Failure place the machine into T and C Mode (refer to OPERATING MODES, page 19)) 2008T Troubleshooting Guide Page 39 PN 490292 Rev.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. Archives
December 2020
Categories |